Celestica D2030 Redstone R0768-F0001-00 48x 10G RJ45 & 4x 40G QSFP+ Ports Switch

Description

Celestica D2030 Redstone R0768-F0001-00 48x 10G RJ45 & 4x 40G QSFP+ Ports Ethernet Switch
With rack mount ears
Used, Fully Tested, 100% Good working Condition,
Celestica
Genuine
There are a few minor scratches on the cover
Will be shipped by FedEx/ DHL immediately after order, could reach you around 5-7 days.
You will get the item shown in the pictures
This price is for 1pcs, we have more than 100pcs in stock
We listed 6pcs on eBay, if you need more please let me know
The shipping cost will be automatically combined if you order more than 1pcs
Any question please feel free to ask me!
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
U-Boot 2009.11(Redstone-T Beta 3.2.0)-svn1478 (Oct 10 2013 - 09:33:36)
CPU0:  P2020, Version: 2.1, (0x80e20021)
Core:  E500, Version: 5.1, (0x80211051)
Clock Configuration:
CPU0:800  MHz, CPU1:800  MHz,
CCB:400  MHz,
DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), LBC:25   MHz
L1:    D-cache 32 kB enabled
I-cache 32 kB enabled
I2C:   ready
DRAM:  Configuring DDR for 666.667 MT/s data rate
DDR:  2 GB
FLASH: 64 MB
L2:    512 KB enabled
NAND:  1024 MiB
EEPROM: NXID v0
eTSEC2 is in sgmii mode.
eTSEC3 is in sgmii mode.
PCIE2: disabled
PCIE1 connected to Slot 2 as Root Complex (base addr ffe0a000)
Scanning PCI bus 01
01  00  14e4  b846  0200  00
PCIE1 on bus 00 - 01
In:    serial
Out:   serial
Err:   serial
Net:   get_phy_info: find the matched ID.
get_phy_info: find the matched ID.
eTSEC3: No support for PHY id ffffffff; assuming generic
eTSEC2, eTSEC3
USB:   PHY Init
Hit Ctrl^C to stop autoboot:  0
Creating 1 MTD partitions on "nand0":
0x000010000000-0x000040000000 : "mtd=5"
Bad block table found at page 524224, version 0x01
Bad block table found at page 524160, version 0x01
nand_read_bbt: Bad block at 0x07b80000
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=5"
UBI: MTD device size:            768 MiB
UBI: number of good PEBs:        6140
UBI: number of bad PEBs:         4
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 6140
UBI: number of PEBs reserved for bad PEB handling: 61
UBI: max/mean erase counter: 27/5
UBI: mtd1 is detached from ubi0
Creating 1 MTD partitions on "nand0":
0x000010000000-0x000040000000 : "mtd=5"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=5"
UBI: MTD device size:            768 MiB
UBI: number of good PEBs:        6140
UBI: number of bad PEBs:         4
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 6140
UBI: number of PEBs reserved for bad PEB handling: 61
UBI: max/mean erase counter: 27/5
UBIFS: recovery needed
UBIFS: recovery deferred
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: mounted read-only
UBIFS: file system size:   741758976 bytes (724374 KiB, 707 MiB, 5749 LEBs)
UBIFS: journal size:       9033728 bytes (8822 KiB, 8 MiB, 71 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root:  0 bytes (0 KiB)
Loading file '/boot/uImage' to addr 0x01000000 with size 2861326 (0x002ba90e)...
Done
Loading file '/boot/p2020rdb.dtb' to addr 0x00c00000 with size 11754 (0x00002dea
)...
Done
Loading file '/boot/rootfs.ext2.gz.uboot' to addr 0x02000000 with size 15623533
(0x00ee656d)...
Done
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
Image Name:   Linux-2.6.32.57_redstone_t
Created:      2017-05-19   6:48:16 UTC
Image Type:   PowerPC Linux Kernel Image (gzip compressed)
Data Size:    2861262 Bytes =  2.7 MB
Load Address: 00000000
Entry Point:  00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name:   uboot ext2 ramdisk rootfs
Created:      2017-05-19   7:02:15 UTC
Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
Data Size:    15623469 Bytes = 14.9 MB
Load Address: 00000000
Entry Point:  00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 00c00000
Booting using the fdt blob at 0xc00000
Uncompressing Kernel Image ... OK
Loading Ramdisk to 2f119000, end 2ffff52d ... OK
Using P2020 RDB machine description
Memory CAM mapping: 256/256/256 Mb, residual: 1280Mb
Linux version 2.6.32.57_redstone_t (fanka@SWEBMYVMM002204) (gcc version 4.2.2) #
1 Fri May 19 14:48:07 CST 2017
Found initrd at 0xef119000:0xeffff52d
Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->255
PCI host bridge /pcie@ffe09000  ranges:
MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000
/pcie@ffe09000: PCICSRBAR @ 0x0
/pcie@ffe09000: WARNING: Outbound window cfg leaves gaps in memory map. Adjustin
g the memory map could reduce unnecessary bounce buffering.
/pcie@ffe09000: DMA window size is 0x0
Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
PCI host bridge /pcie@ffe0a000  ranges:
MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
IO 0x00000000ffc30000..0x00000000ffc3ffff -> 0x0000000000000000
/pcie@ffe0a000: PCICSRBAR @ 0xfff00000
MPC85xx RDB board from Freescale Semiconductor
Zone PFN ranges:
DMA      0x00000000 -> 0x00030000
Normal   0x00030000 -> 0x00030000
HighMem  0x00030000 -> 0x00080000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00080000
MMU: Allocated 1088 bytes of context maps for 255 contexts
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 520192
Kernel command line: root=/dev/ram rw console=ttyS0,115200 ramdisk_size=3000000
cache-sram-size=0x10000
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2057836k/2097152k available (5508k kernel code, 38432k reserved, 256k da
ta, 139k bss, 192k init)
Kernel virtual memory layout:
* 0xfffef000..0xfffff000  : fixmap
* 0xff800000..0xffc00000  : highmem PTEs
* 0xff7da000..0xff800000  : early ioremap
* 0xf1000000..0xff7da000  : vmalloc & ioremap
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:512
mpic: Setting up MPIC " OpenPIC  " version 1.2 at ffe40000, max 2 CPUs
mpic: ISU size: 256, shift: 8, mask: ff
mpic: Initializing for 256 sources
clocksource: timebase mult[5000000] shift[22] registered
Console: colour dummy device 80x25
Mount-cache hash table entries: 512
xor: measuring software checksum speed
8regs     :   943.000 MB/sec
8regs_prefetch:   817.000 MB/sec
32regs    :  1016.000 MB/sec
32regs_prefetch:   899.000 MB/sec
xor: using function: 32regs (1016.000 MB/sec)
NET: Registered protocol family 16
PCI: Probing PCI hardware
pci 0001:01:00.0: ignoring class b20 (doesn't match header type 01)
pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0001:01:00.0: PME# disabled
pci 0001:02:00.0: PME# supported from D0 D3hot D3cold
pci 0001:02:00.0: PME# disabled
pci 0001:01:00.0: PCI bridge, secondary bus 0001:02
pci 0001:01:00.0:   IO window: 0x00-0xffff
pci 0001:01:00.0:   MEM window: 0xc0000000-0xdfffffff
pci 0001:01:00.0:   PREFETCH window: disabled
pci 0001:01:00.0: enabling device (0106 -> 0107)
bio: create slab at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
raid6: int32x1    114 MB/s
raid6: int32x2    186 MB/s
raid6: int32x4    271 MB/s
raid6: int32x8    234 MB/s
raid6: using algorithm int32x4 (271 MB/s)
Freescale Elo / Elo Plus DMA driver
Swit
Menu:
1.zebos CLI
2.linux shell
3.tech support
Choose:
Menu:
1.zebos CLI
2.linux shell
3.tech support
Choose:1
ZebOS version 7.8.2 IPIRouter 05/19/2017 14:38:40
Tencent-S48T>en
Tencent-S48T#
show version
HW Platform:S48T    Vendor:Celestica
Software:tswitch_V4.2R050(based on ZEBOS 7.8.2) Svn Revision: 7402
Kernel:Linux 2.6.32.57_redstone_t
Compiled time:05/19/2017 14:38:40 by fanka
Compiled path:/home/fanka/tswitch/D2030/base/TSwitch_V4.2R050D002/zebos
SVN URL: https://tc-svn.tencent.com/apd/apd_sys_rep/tswitch_proj/tags/TSwitch_V4
.2R050D002/zebos
Compiled flags:-g -O0 -DCONFIG_REDSTONE_T
Copyright (C) 2010-2015 Tencent Inc.  All rights reserved.
Switch uptime is 0 days, 0 hours, 2 mins, 17 secs
CPU                : e500v2
Platform           : P2020 RDB
Memory             : 2048 MB
Broadcom chip      : Broadcom 56846
Base MAC Address   : 00:e0:ec:40:84:cb
Vlan1 MAC Address  : 00:e0:ec:40:84:cb
Tencent-S48T#
Tencent-S48T#
show ?
aaa                   Authentication, Authorization & Accounting
arp                   Address Resolution Protocol (ARP)
bfd                   Bidirectional Forwarding Detection (BFD)
bgp                   Border Gateway Protocol (BGP)
class-map             Class map entry
cli                   Show CLI tree of current mode
clock                 Display Current Date
cpu                   CPU
debugging             Debugging functions (see also 'undebug')
diag                  Display diagnostic information
ecmp                  L3 Mulitipath
etherchannel          Etherchannel commands
history               Display the session command history
hw                    Hardware, four sensors etc
interface             Interface status and configuration
ip                    Internet Protocol (IP)
ip-access-group       List IP access groups
lacp                  LACP commands
lacp-counter          LACP commands
list                  Show command lists
lldp                  Link Layer Discovery Protocol
log                   Show log
mac                   Layer 2 MAC entries
mac-access-group      List MAC access groups
mac-acl               List MAC access lists
mac-address-table     Layer 2 MAC address table
memory                Display Memory
mgmt                  Management
mirror                Port Mirroring
nsm                   NSM
ntp                   Network time protocol
ospf                  OSPF information
platform              Internet Protocol (IP)
policy-map            Policy map entry
port                  port commands
privilege             Show current privilege level
proc-names            Show process names
process               Process
qos                   Quality of Service.
qos-access-list       List QoS (MAC & IP) access lists
route-map             route-map information
router-id             Router ID
running-config        Current Operating configuration
sflow                 sFlow protocol
spanning-tree         Spanning-tree Display spanning tree information
startup               Startup information
startup-config        Contents of startup configuration
static-channel-group  Static channel commands
storm-control         The layer2 interface
tacacs+               Modify TACACS+ query parameters
tech-support          Show router technical information
transceiver           Transceiver information
version               Display ZebOS version
vlan                  Display VLAN information
vrrp                  VRRP protocol
Tencent-S48T#